Standard Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale) 1. Scope 1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion. ASTM C652 - Standard Specification for Hollow Brick Standard Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale) 1. Scope 1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion.
Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings:ASTM D 3747 :1979 :SPECIFICATION FOR EMULSIFIED ASPHALT ADHESIVE FOR ADHERING ROOF INSULATION:ASTM D 6356 :1998 :Standard Test Method for Hydrogen Gas Generation of Aluminum Emulsified Asphalt Used as a Protective Coating for Roofing:ASTM D 5404 ASTM D4414 - 95(2020) Standard Practice for Measurement 4.1 Wet film thickness measurements of coatings applied on articles can be very helpful in controlling the thickness of the final dry coating, although in some specifications the wet film thickness is specified. Most protective and high performance coatings are applied to meet a requirement or specification for dry film thickness for each coat or for the completed coating system, or for both. ASTM F1518-00 - Standard Practice for Cleaning and ASTM F1518-00 Standard Practice for Cleaning and Disinfection of Flexible Fiberoptic and Video Endoscopes Used in the Examination of the Hollow Viscera. 1.1 This practice covers the flexible fiberoptic and video endoscopes that are fully immersible in liquid and are used in the examination of the hollow viscera (that is, colonoscopes
1.1 This accelerated test method is used to determine the relative resistance of steel pipeline coatings to penetration or deformation by a blunt rod under a specified load. The test method is intended to apply to the testing of all types of nonmetallic pipeline coatings subjected to various temperatures. Common Coating Inspection Practices, Standards & ASTM D 523 Test Method for Specular Gloss Gloss reading should be an average of 3 readings per area. Gloss is measured at angles of 20°, 60° and 85°. 85° is used for low gloss coatings, 20° for high gloss coatings and 60° at all gloss levels. Tnemec used 60° gloss readings at the following levels across our product line. HOLLOW MANUAL METAL NAAMM STANDARD HMMA 8Since both types of sheets are used for hollow metal work, it is important that the distinction between the two be clearly recognized. .1 Electrolytic Coated Steel Electrolytically coated steel has a much thinner zinc coating than steel coated by the hot dip process. The standard referenced for such sheets is ASTM A591, "Standard Specification for
AS/NZS 4792:Hot-dip galvanized (zinc) coatings on ferrous hollow sections, applied by a continuous or a specialized process. This Standard specifies requirements for the mass, quality & testing of hot-dip galvanized coatings applied to:Hollow sections galvanized on both surfaces in a specialized plant e.g. signposts to HDG300; New ASTM standard enhances hollow structural sections ASTM A1085 is the only HSS specification used in North America or Europe that limits the maximum yield stress. Standard requirement for notch toughness. The specification will require all HSS to meet a minimum Charpy V-notch (CVN) value of 25 ft-lb at 40°F, which corresponds to New ASTM standard enhances hollow structural sections ASTM A1085 is the only HSS specification used in North America or Europe that limits the maximum yield stress. Standard requirement for notch toughness. The specification will require all HSS to meet a minimum Charpy V-notch (CVN) value of 25 ft-lb at 40°F, which corresponds to
Pre-fatigue static testing per ASTM F1044 can be used to determine starting stress levels for fatigue testing. Tensile Testing:ASTM F1147 (Standard Test Method for Tension Testing of Calcium Phosphate and Metallic Coatings) describes tensile testing of calcium phosphate and metallic porous coatings adhering to dense metal substrates. SECTION 08111 - STANDARD STEEL DOORS AND FRAMES1. Standard hollow-metal steel doors. 2. Standard hollow-metal steel frames. B. Related Sections include the following:1. Division 07 Section JOINT SEALANTS for sealants used in hollow metal frame installation. 2. Division 08 Section GLAZING for glazed lites in standard steel doors. 3. Specifying and Detailing for Hot-Dip Galvanizingproject, ASTM A123/A123M-02, Standard Specication for Zinc (Hot-dip Galvanized) Coatings on Iron and Steel Products should be the cornerstone of your project speci-cation. ASTM A123 applies to structural Keep the following details in mind when developing and
compatible with the resin system used. 5.2.3 ResinA chemically resistant isophthalic based poly-ester, or vinyl ester thermoset resin and catalyst system or an 6 Annual Book of ASTM Standards, Vol 08.04. 7 Annual Book of ASTM Standards, Vol 05.03. 8 Available from the American Water Works Association, 6666 W. Quincey Ave., Denver, CO 80235. Standard Test Methods for Mastics and Coatings Used Standard Test Methods for Mastics and Coatings Used With Thermal Insulation1 This standard is issued under the xed designation C 461; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A Test Procedure & Acceptance Criteria:Factory Applied ASTM D3359-02, Standard Test Method for Measuring Adhesion by the Tape Test. ASTM D4060-01, Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser. ASTM D610-01, Standard Test Method for Evaluating Degree of Rusting on Painted Steel Surfaces. ASTM D714-02, Standard Test Method for
ASTM's steel standards are instrumental in classifying, evaluating, and specifying the material, chemical, mechanical, and metallurgical properties of the different types of steels, which are primarily used in the production of mechanical components, industrial parts, and construction elements, as well as other accessories related to them.
Post A Require